MITSUBISHI FR-A024 MANUAL PDF

Embed Size px x x x x Thank you for choosing the Mitsubishi Inverter. This instruction manual gives handling informalion and precautions for use of this equipment. Incorrect handling might cause an unexpected fault. Before using the inverter, please read this manual carefully to use the equipment to its optimum. Please forward this manual to the end user.

Author:Fenrik Kazicage
Country:Austria
Language:English (Spanish)
Genre:Finance
Published (Last):2 December 2015
Pages:384
PDF File Size:10.12 Mb
ePub File Size:3.56 Mb
ISBN:168-3-36616-895-1
Downloads:95429
Price:Free* [*Free Regsitration Required]
Uploader:Voodoojinn



Embed Size px x x x x Thank you for choosing the Mitsubishi Inverter. This instruction manual gives handling informalion and precautions for use of this equipment. Incorrect handling might cause an unexpected fault. Before using the inverter, please read this manual carefully to use the equipment to its optimum. Please forward this manual to the end user. This section Is speclfically about safety mattersDo not attempt to install, operate, maintain or insped the inverter until you have read throug, pM p this instruction manualand a e documents carefuliyand can u s the equipment correctl Do not use the inverter until you have a full knowledge of the equipment, safety information an' instructions.

Assumes that incorrect handling may cause hazardous conditions, resulting in death or severe injury. Assumes that incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause physical damage only.

Please follow the instructions of both levels because they are important to personnel safety. While power is on or when the inverter is running, do not open the front cover. You may get an electric shock. Do not run the inverter Ath the front cover removed.

Otherwise, you may access the exposed high-voltage terminals and charging parl and get an electric shock. I power is OH, do not remove the front cover except for wiring or periodic inspection. Before starting wiring or inspection, wHch power OH, wait for more than 10 minutes, and check for no residual voltage with a tester. Use a class 3 or higher earthing method to earth t h e inverter. Any person who is involved in the wiring or inspection of this equipment should be fully competent to do the work.

Always install the inverter before wiring. Otherwise, you may get an electrr. Operate the switches with dry hands to prevent an electric shock. Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Installing the inverter directly on or near a combustible surface could lead to a fire. A continuous flow of a large current could cause a fire. Failure to do so could cause the brake resistor to abnormally overheat and a fire to start if a fault occurs in the brake transistor, etc.

Do not connect the resistor directly to the DC terminals P,N. Thls could cause a fire. Apply only the voltage specified in the instruction manual to each terminal to prevent damage, etc. Ensure that the cables are connected to the correct terminals. Otherwise, damage, etc. Always make sure that polarky is correct to prevent damage, etc. While power is on or for some time after power-off, do not touch the inverter or brake resistor as these will be not and you may be burned.

To prevent injury, damage, or product failure please note the following 1 Transpotation and mounting,. Do no1 operate a the inverter is damaged or has parts missing. Do not lift he inverter with the front cover attached. It may fall off, Do not stand or rest heavy objects on the inverter. Check the inverter mounting orientation is correct. Prevent any dust, wire fragments or other foreign bodies from dropping into the inverter during wiring up and commissioning. Do not drop the inverter, or subject it to impacts.

Use the inverter under the following environmental conditions:. Do not fit capacitive equipment such as power factor correction capacitor, noise filter or surge suppressor onto the output of the inverter.

The connection orientalion of the output cables U, V, W to the motor will affect the direction of rotation of the motor. The stop key is valid only when furrtion setting has been made. Prepare an emergency stop switch separately. Switch off the start signal when resetting the inverter. Failure to do so may start the motor immediateiy after reset. If another electric device is connected to the inverter output, the device could be damaged Do not modify the equipment.

The electronic motor thermal protection does not guarantee lo prevent motor burn out. Do not use a contactor on the inverter input f o r lrequent startinwstopping of the inverter, use control signals. To reduce the effect of mains conducted electromagnetic interference, use a RFI noise finer.

Take care to ensure that electromagnetic radiation from the inverter does not damage or affect the operation of nearby electrical equipment. When driving a V class W r with the inverter, use an insulation-enhamed motor, or measures should be taken to suppress the surge vottage.

Surge vonages atributable to the wiring constant may occur at motor terminals, deterioraling the insulation of the motor. When parameter clear or all parameter clear is performed, each parameter returns to the factory setting.

Re-set the requlred parameters before starting operation. The inverter can be easiiy set for high-speed operatin. W o r e changing its setting, fully examine the performances of the motor and machine. The inverter does not have a holding stop facility. For emergency stop, another circuit must be used.

Provide a safety backup such as an emergency brake which wiil prevent the machine and equipment from hazardous conditions if the inverter fails. Never mn the inverter like this. Always replace the cover and follow this instruction manual when operating the inverter. Handle the Inverter carefully; refer to the description and caution information provided in this manual.

If H is used to start or stop me Inverter, it will damage. Choose a reactor according to me inverter model:. Installation L d o n The service Iile of me inverter is influenced by temperature. Ambient temperature should be held Whin the specified l m i k adequate heat dissipation. The control signal ihnes must be run as far from me main clrcuit as possible s mat me inverter wl not be atfected by o il. I Parametem to be set it general-purpose magnebc flux vector control mode is selected refer to page 5 3.

Post on Apr 2. Category: Documents download. Fire Prevention a Mount the inverter and brake resistor on a noncombustible surface. Injury Prevention AL Apply only the voltage specified in the instruction manual to each terminal to prevent damage, etc. Additional instructions pw o.

Use the inverter under the following environmental conditions: Temperatures applicable for a short time, e. IRefer to:lp. Choose a reactor according to me inverter model: Installation L d o n The service Iile of me inverter is influenced by temperature.

DIERCKE WELTATLAS 2008 PDF

mitsubishi freqrol fr a024 manual

Embed Size px x x x x Thank you for choosing the Mitsubishi Inverter. This instruction manual gives handling informalion and precautions for use of this equipment. Incorrect handling might cause an unexpected fault. Before using the inverter, please read this manual carefully to use the equipment to its optimum. Please forward this manual to the end user.

RECETTE BABYCOOK PDF

Mitsubishi-Freqrol-FR-A024-Manual.pdf

.

GRUNDFAHRAUFGABEN MOTORRAD PDF

User Manual for HPE Mitsubishi Freqrol FR A024 Manual

.

ISO TS 24817 PDF

2HP 230V Mitsubishi VFD, Inverter, AC Drive FR-A024-1.5K

.

Related Articles