Manual zz. Version 1. Retain Instructions: The safety and operating instructions should be retained for future reference. No user serviceable parts inside; refer servicing to qualified personnel. To reduce the risk of fire or electric shock, do not expose this device to rain and moisture.
|Published (Last):||27 December 2010|
|PDF File Size:||11.9 Mb|
|ePub File Size:||9.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
Manual zz. Version 1. Retain Instructions: The safety and operating instructions should be retained for future reference. No user serviceable parts inside; refer servicing to qualified personnel. To reduce the risk of fire or electric shock, do not expose this device to rain and moisture. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature.
Please read the manual. Heed Warnings: All warnings on the device and in the operating instructions should be adhered to. Follow instructions: All operation and user instructions should be followed. Water and Moisture: The device should not be used near water e. Ventilation: The device should be situated so that its location or position does not interfere with its proper ventilation. For example, the device should not be placed on a bed, sofa, rug, or similar surface that may block the ventilation openings, or used in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
Heat: The device should be situated away from heat sources such as radiators, heat registers, stoves, or other devices including amplifiers that produce heat. Power Source: The device should only be connected to a power supply of the type described in the operating instructions or on the device.
Grounding or Polarization: This device must be grounded. Power Cords: Power cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, sockets, outlets and the point where they exit from the device.
Cleaning: The device should be cleaned only as recommended by the manufacturer. Non-use Periods: The power cord of the device should be unplugged from the outlet when left unused for a long period of time. Damage Requiring Service: The device should be serviced by qualified service personnel when: s The power cord or the plug has been damaged; or s Debris or liquid has entered the device; or s The device has been exposed to rain; or s The device does not appear to operate normally or exhibits a pronounced change in performance; or s The device has been dropped, or the enclosure damaged.
Servicing: The user should not attempt to service the device beyond that which is described in the operating instructions. All other servicing should be referred to qualified service personnel. Well, for over 30 years, my passion has been music and electronics.
DAT recorder and a monitor system consisting of monitor loudspeaker s and power amplifier except for UB The design work, the entire circuit diagram and PCB development, and even the mechanical concepts are my own work. My vision was to enable you, the user, to give free rein to your true potential and creativity.
The result is incredibly powerful mixing consoles that offer intuitive operation. They cannot fail to impress with their extremely flexible routing possibilities plus fantastic wealth of functions.
And extraordinarily high-quality components provide unrivalled reliability, even under extreme loads. Thank you for the confidence you have placed in us by purchasing the UB mixing console. I should also like to thank all those who, with their personal commitment and passion, have helped me realize this impressive series of mixing consoles.
Always be careful to set appropriate volume levels. All other mixer functions can be included in this main function. In order to help you understand the links between the controls, we have arranged them in groups according to their function.
The illustrations at the beginning of each chapter show the controls described in each respective chapter. Nevertheless, we you carefully examine the packaging and its signs of physical damage, which may have transit. The console is connected to the mains via the supplied cable. The console meets the required safety standards.
Blown fuses must only be replaced by fuses of the same type and rating. First connect the power supply unit to the console, then connect the power supply unit to the mains. Please note that all units must be properly grounded.
For your own safety, you should never remove any ground connectors from electrical devices or power cables, or render them inoperative. Please ensure that only qualified people install and operate the mixing console. During installation and operation, the user must have sufficient electrical contact to earth, otherwise electrostatic discharges might affect the operation of the unit.
Please mute your playback system before you activate the phantom power supply to prevent switch-on thumps being directed to your loudspeakers.
Please also note the instructions in chapter 2. Unbalanced devices mono jacks can also be connected to these inputs. You can never use both simultaneously! This control should always be turned fully counterclockwise whenever you connect or disconnect a signal source to one of the inputs. All bands provide boost or cut of up to 15 dB. In the central position, the equalizer is inactive. Alternatively, you can use our online registration option available on the world wide web www.
You will find the serial number on the rear of your mixing console. All controls, switches and connectors will be discussed in detail. The cut-off frequencies of the upper and lower band are 12 kHz and 80 Hz respectively. The return from the effects unit is then brought back into the console on the aux return connectors UB or normal channel inputs.
If this were not the case, the effects signal of the channel would remain audible even when the fader is lowered to zero. This control features a constant-power characteristic, which means the signal is always maintained at a constant level, irrespective of position in the stereo panorama. However, since the FX send buses are both mono, a mono sum is first taken from the stereo input before it is sent to the FX bus. The UB is not equipped with FXsends. If a channel is operated in mono via the left line input, this control has the same function as the PAN control used in the mono channels.
The stereo channels are designed to handle typical line level signals. Both inputs will also accept unbalanced jacks. The filter characteristics and cut-off frequencies are the same as those in the mono channels.
You can instead use these connectors as additional inputs, but any effects 2. This does, however, give you the ability to use the channel EQ on the effects return signal if you wish. Alternatively the line or tape output of a hi-fi amplifier with source selection switch could also be hooked up here, allowing you to easily listen to additional sources.
This provides an easy way to monitor signals coming back from tape to ensure that they are recording correctly. The UB is not equipped with control room outputs. The main mix signal appears here at a level of 0 dBu. CD player, tape deck, etc.
Connect the microphones before you switch on the power supply. After switching on, wait approx. Then use the GAIN controls to increase the input amplification until signal peaks show 0 dB on the level meter. While analog recorders can be overloaded to some extent, creating only a certain amount of distortion which is common and often desirable , digital recorders distort quickly when overloaded.
In addition, digital distortion is not only undesirable, but also renders your recording completely useless. A recording level of 0 dB is recommended for all signal types.
Use the AC adapter supplied to connect the console to the mains. The adapter complies with all applicable safety standards. First connect the console to the power supply unit, then connect the power supply unit to the mains.
This is completely normal. The illustrations below show how the connectors should be wired. Be sure to use only high-grade cables. Please use commercial RCA cables to connect the 2-track inputs and outputs. To do this, use either mono plugs or stereo plugs with the ring and sleeve bridged pins 1 and 3 in the case of XLR connectors. As a result of these efforts, modifications may be made from time to time to existing products without prior notice.
Specifications and appearance may differ from those listed or illustrated. Failure to return the card in due time date as per postmark will void any extended warranty claims. Based on the conditions herein, the buyer may also choose to use the online registration option via the Internet www.
If the warranty claim proves to be justified, the product will be returned to the user freight prepaid. Warranty claims other than those indicated above are expressly excluded.
Any repair or opening of the unit carried out by unauthorized personnel user included will void the warranty. Such costs will also be invoiced separately when the buyer has sent in a written repair order. All inquiries must be accompanied by a description of the problem. Shipments without freight prepaid will not be accepted. This warranty is extended exclusively to the original buyer customer of retail dealer and is not transferable to anyone who may subsequently purchase this product.
No other person retail dealer, etc. The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH. Behringer Eurorack UB User manual.
Behringer Europack UB1002FX Owner's Manual
Even though most of the tasks in a studio can nowadays be. The extensively equipped main section of. Your monitor speakers are. Connect the outputs of the sound card in your. Recording and playback:.
Please select a division you are interested in: